Posts Tagged ‘bodice’

h1

Pattern Drafting 101 – The Basic Bodice Sleeve Block

19 July, 2010

So, I’ll admit, I kinda dropped the ball on updating this week. No excuses, though, so here it comes. All the updates from the past week. One right after the other.

First up, the Set-In Sleeve block. This pattern is going to be made to fit, and thus will be based on, the Basic Bodice Block you made in the previous post.

You will need paper, a pencil, a ruler, and a french curve.

* ** *** ** *
Because the original measurements are metric, and their US standard equivalents would be near impossible to accurately measure (1/5 of an inch?), I’m going to stick with the metric measurements.
* ** *** ** *

Step 1: Trace on the top of the bodice block, from the base of the armscye, up. You can do this either by copying the shape to a new large piece of paper or cardboard, or by using a tracing paper overlay. Be sure to include the point labels; you’ll be needing them a lot.

Step 2: Extend Point T vertically so that it passes through point Y, touching the edge of the armscye.

Step 3: Mark the point above point T one third of the total armscye measurement, not the half armscye measurement we were using before on the main bodice. Label this point AC.

Step 4: Draw a new line horizontally at the level of point Y, midway between points T and AC.

Step 5: Mark the point where the line from Y crosses the left-most edge of the armscye curve. Label that point AD.

Step 6: Mark the point halfway between points T and Y. Label that point AE. Draw a very short horizontal line across to the ARMSCYE curve and mark the intersection. Label that point AF.

Step 7: Measure the length of the ARMSCYE curve between point AF and point X at the top – not the length of the straight line connecting points AF and X, but the distance ALONG the curve. To do this, drape a small piece of string along the curve and then measure the length of the string when it is straightened out.
Now, add 1 cm to this (for bust sizes 94cm-107cm, add 1.25cm. For bust sizes above 107cm, add 1.5cm.) Zero the ruler at AF, and pivot the ruler until this length meets the horizontal line at AC. Mark the point at the intersection point AG.

Step 8: Measure the distance again along the curve between the point AD and Point I at the top of the left part of the armscye curve.
Add 1cm to this distance (1.25cm for bust sizes 94-107cm, 1.5cm for bust sizes larger than 107cm.) Zero the ruler at point AF, and pivot the ruler until the intersection with the horizontal line at the Y level corresponds to the length just calculated. Label this p‌oint AH.

Step 9: Measure the distance from Z to AF along the curve. Subtract 0.3cm. Zero the ruler at point AE, and pivot the ruler until the intersection with the horizontal line that passes through point T corresponds to the length just calculated. Label this p‌oint AI.

Step 10: Measure the distance from AD to Z along the curve. Subtract 0.3cm. Zero the ruler at point AH, and pivot the ruler until the intersection with the horizontal line that passes through points T and Z corresponds to the length just calculated. Label this p‌oint AJ.

Step 11: Drop a line vertically from the summit point AG. This line will be the length of the sleeve measurement, taken from the top of the shoulder to the wrist. Mark the end point AK.

Step 12: At this point in construction the basic bodice you traced earlier is no longer needed. Go ahead and erase any of the unused lines and points. They won’t be shown in any of the diagrams beyond this point, just to keep things clear and easy to follow.

Step 13: Drop a vertical line from points AI to the horizontal line passing through point AK. Mark this new point AL. Drop another vertical line from point AJ to the same horizontal line. Mark this new point AM. Draw a new horizontal line from AL to AM.

Step 14: Draw in a curve from AI to AH, hollowed below the diagonal by a maximum of 0.75cm.

Step 15: Continue the curve above the line from AH to AG, raised 1 cm at maximum deviation. Make sure that the curve flattens to the horizontal as it passes through point AG.

Step 16: Continue the curve downwards to point AE, passing 2 cm at maximum deviation above the line connecting AG and AE.

Step 17: Finish the curve of the sleeve head, dropping it below the line connecting AE and AI by 1 cm at maximum deviation, and making sure it approaches the horizontal at point AI. Note that the sleeve head shape is asymmetrical – this is as it should be.

Step 18: If you wish to introduce some shaping into the sleeve, you may narrow the sleeve by a distance of from 1 to 3 cm on each side. This is completely optional. If you do, mark your new points AN (1-3cm in from point AL) and AO (1-3cm in from point AM)

Step 19: Lower the sleeve edge curve by 1 cm on the section between AN and AK (the back section of the sleeve). Raise the sleeve edge curve by 1cm on the section between AK and AO (the front section of the sleeve).
*If you chose to skip the shaping, replace “AN” with “AL” and “AO” with “AM”

Step 20: This is the final outline of the sleeve. The waist line on the bodice block marks the location of the elbow on the sleeve.

Ta-Da! You’re done! Enjoy the endless possibilities your new personalised sloper will bring!

Advertisements
h1

Pattern Drafting 101- Drafting the Basic Bodice Block

14 July, 2010

The Basic Bodice Block- the only pattern you’ll ever need to make any kind of garment for the upper body- tees, blouses, tanks, sweaters, coats, vests, even bras! Drafting the Basic Bodice Block requires a knowledge of basic high-school geometry, but once you’ve finished, you have a universal pattern for all your upper body sewing needs fit to your own body, not to a set of predetermined body measurements based on the “average” person.

(These instructions taken from Gedwoods of Burdastyle.com. I have simply rewritten them for ease of reading. His original instructional post can be found here.)

First things first, you will need:

  1. Your body and a measuring tape
  2. a ruler, preferably a long one
  3. a large pad of paper, or several sheets of printer paper taped together. Your paper should be 2″ wider than half your bust measurement.
  4. pencils and erasers
  5. a french curve, specifically one designed for working armholes and necklines

*  **  ***  **  *

Because the original measurements are metric, and their US standard equivalents would be near impossible to accurately measure (1/5 of an inch?), I’m going to stick with the metric measurements.

*  **  ***  **  *

Step 1: Mark Your Origin. Orient your paper in landscape orientation, or with the longest dimension running horizontally in front of you. Mark a point  in the upper left hand corner about 1cm from either edge of the paper. This is your origin point, your home base, and all your measurements and lines are going to be based on this point. Mark this point O.

Step 2: Square Off. From your origin point O, measure down 1.5cm parallel to the vertical edge of the paper and draw a line to that point. Mark that point A.

Step 3: Armscye Depth. From point A, you will now measure down the armscye depth plus 0.5cm. The armscye is half the circumference of the arm at the shoulder joint. Mark the end point B.

Armscye Depth

Step4: Bust Width. From point B, draw a line perpendicular to line AB. This line will be half the length of the bust measurement plus 5cm. Mark the end point of that line C.

Step 5: Drawing upwards from point C, draw a line parallel to line OB, for the same distance as the length of OB. If your bust measurement is 92cm or below, mark this point D. For bust sizes above 92cm, get out your calculator- you’re going to add 1/8th of the distance above 92cm. For example, someone with a 100cm bust measurement is 8cm above 92cm. 1/8th of 8cm is 1cm. Add this amount to the line you just drew off of point C, and mark the endpoint D. Draw a light line connecting points D and O. You’ll be erasing this line later.

Upwards from Point C

Step 6: Return to Point O. Drawing straight down again from point O, parallel to the vertical edge of the paper, mark the distance from the nape of the neck to the waist. I have a trick for finding the nape of my neck: Tip your head back as far as it will go, and rest two fingers on your neck where the back of the head and the back of the neck meet. Don’t force them into the crevice, just rest them there so that the tops of your fingers are touching your head and the bottoms are on your neck. Lift your head again, and your middle finger will be on your nape. The waist is the smallest point of the torso, and can be found by tying a narrow strip of elastic snuggly around your waist and bending your body- the elastic will roll to the narrowest part of your torso, your waist. Measure along the spine between these two points. Mark the endpoint of this new line point E.

Step 7: Square off as shown below. Mark the corner point F.

 

Squaring Off

Step 8: The Neck. Go back to point O, and measure across 1/5th of the neck measurement (taken around the neck at the nape) minus 0.2cm. Mark this point G. You need not connect points O and G, but if you choose to, draw the line lightly, as it will need to be erased later.

Step 9: Using the French Curve, draw a shallow curve from points A to G. This is your back neckline edge.

 

Constructing The Back Neckline Edge

Step 10: Returning to Point A. Measure down from point A 1/5th of the armscye measurement minus 0.7cm. Mark this point H. From Point H, draw a line perpendicular to the line OB that is half the distance of line BC (see illustration below).

Step 11: Shoulder Measurement. The shoulder measurement is somewhat tricky to get; you will probably need a second set of hands to help you out. To measure the shoulders, stretch the measuring tape across your back, from the very end of one shoulder to the very end of the other. Make a note of the measurement, you will need it later. Now, with your ruler zeroed on point G, pivot your ruler until the distance you need to mark (1/2 of the Shoulder Measurement + 1cm) intersects with the line your drew in Step 10. Mark the intersection point I. (A reader pointed out to me that these two lines may not intersect smoothly. If you’re finding that Line H is too short to accommodate your shoulder measurement, go ahead and extend line H out to fit. Remember, this sort of thing is based on averages and the “average” body structure, but in reality, not everyone conforms to that average.)

Finding the Shoulder

Step 12: Find the Point halfway between points G and I. Mark that point J. From point J, measure 5cm down and 1cm to the left. Mark this point K. Point K is the end of the shoulder dart.

Step 13: From Point K, draw two diagonal lines up to line GI. They should intersect with the line 1cm apart, and the lines should be of equal length.

The Back Shoulder Dart

Step 14: Back Measurement. From point B, measure and mark half the back measurement plus 0.5cm along the line BC. An easy way to obtain the back measurement is to put on a fitted t-shirt and measure across the back from armscye seam to armscye seam at the narrowest point (across the shoulder blades). Mark this point L.

Step 15: Square up from point L to the line HI. Mark the intersection point M. Be sure to pencil in this line lightly, as you’ll be erasing it later on.

 

Squaring Off Again

Step 16: Find the point halfway between L and M. Mark this point N. Also, find the point halfway between B and L. Mark this point P. Measure the distance between B and P, and mark this distance along the horizontal line from point E. Mark the end point Q. Draw a dashed line from Point P to Point Q.

Step 17: Moving to the Other Side, measure 1/5th of the neck measurement plus 0.7cm from point D, along the line DO. Mark this new point R.

Moving Along...

Step 18: Measure Down from point D 1/5th of the neck measurement minus 0.2cm. Mark this point S.

Step 19: Using your French Curve, draw a deep curved line from point R to point S. This is the front neckline edge.

 

Front Neckline Edge

Step 20: Bust Dart. From point C, measure towards point B the distance on 1/2 the Chest measurement plus 1/2 the dart size. Mark that Point T. This part can get a little tricky. To obtain the chest measurement, subtract the back measurement from the bust measurement. The dart size is not actually a measurement, but it is scaled with the bust size. To find your dart size, start with a 7cm dart and add 0.6cm to it for every 4 cm of bust above 88cm. Subtract the same amount from 7cm for every 4cm of bust below 88cm. So, a 100 cm bust has a 8.8cm dart, while a 84cm bust has a 6.4cm dart. Make note of your dart size. Draw a vertical line up from point T to just below line HI.

Step 21: Find the Halfway Point between points C and T. Mark this point U. Draw a dashed vertical line downward to intersect with line EF. Mark the intersection point V. This is the mid front line.

 

The Mid-Front Line

Step 22:  Mark the Bust Point 2.5 cm below point U. Mark this point BP.

Step 23: Using the Dart Size from step 20, measure from point R along the line DO. Mark the resulting point W. Now draw a line from point R to the Bust Point (BP), and from point BP to point W. These are the sides of your bust dart.

 

The Bust Dart

Step 24: Shift Your Attention to the construction line passing through points H, M, and I. Measure down 1.5cm and lightly draw in a new construction line, parallel to the first, across the middle of the block.

Step 25: Repeat the Pivoting Motion we did in step 11. Zero your ruler on point W and pivot the ruler until it crosses the construction line at the distance of the shoulder measurement. Mark this intersection point X.

 

Pivoting Again

Step 26: Measure Upwards 1/3 of the armscye depth measurement from point T and mark that point Y. Find the halfway point between points L and T. Mark that point Z. Draw a dashed vertical line down from point Z until it intersects the waistline (line EF), and mark that intersection point AA.

Step 27: Draw A Small Diagonal inward-pointing line from Point L and Point T. The length of that line will vary depending on your bust size.

Bust Measurement L Length T Length
82cm or smaller 2.25cm 1.75cm
82-94cm 2.5cm 2cm
94-107cm 3cm 2.5cm
Above 107cm 3.5cm 3cm

Step 28:Using your French Curve, draw in the armscye curve so that it passes smoothly through the construction points I-M-L Segment-Z-T Segment-Y-X.

 

Drawing in the Armscye

Step 29: Extend the line DF downwards by 0.5 – 1.5cm, depending on your bust measurement (0.5cm for small, 1.0cm for intermediate, 1.5cm for large). Mark the endpoint AB. Draw a line from AB to E. This ensures that the waist remains horizontal and doesn’t ride up.

Extending the Line

Step 30: Draw in Darts around each of the threedashed lines that extend from the lower boundary of the block (line AB to E) to the line BC. And this is where Gedwood’s directions become a little fuzzy and convoluted, so I’m going to attempt to unravel them:

(Thanks to Muushka for helping me to clarify these instructions!) At the end of this, what’s left of line E AB should measure out to ((Bust Measurement +3) + (Waist Measurement + 6))/2. For example, if you’re working with an 88cm bust and a 65cm waist, the math should go as follows

((88+3)+(65+6))/2

88+3=91
65+6=71
91-71=20 (This is the amount that needs to be taken out in darts all around)
20/2= 10 (This is how much we need to take out in darts on the pattern)

Dividing up the darts as evenly as possible, we get Back=3cm, Side=3cm, Front=4cm

Drawing in the Darts

Step 31: Redraw Your Block outline and cut along these lines to get the final, close-fitting basic bodice block!

 

The Final Product